Fitilar LED sune mafi mashahuri zaɓi a cikin masana'antar hasken wuta ta zamani. Waɗannan filayen LED sun shahara musamman don DIY, godiya ga sassauci da ƙarfinsu. Yawancin lokaci suna zuwa cikin tsayin mita 5 (daidaitaccen girman amma yana iya bambanta) wanda zaku iya girma gwargwadon buƙatun ku. Kuma game da wannan girman, tambayar da aka fi sani shine- za ku iya yanke hasken tsiri na LED? Kuma yadda za a sake haɗa su bayan yanke?
PCB na LED tsiri yana da wasu alamun kunnen dot na jan karfe wanda ke biye da gunkin almakashi. Waɗannan gumakan almakashi suna nuna maki yanke na fitilun LED. Ainihin, wannan shine sashe inda ɗayan kewayawa ya ƙare ɗayan kuma yana farawa. Don haka, yanke a wannan lokacin yana da aminci gaba ɗaya kuma ba zai lalata igiyoyin LED ba. Koyaya, akwai kuma zaɓuɓɓuka don sake haɗa sassan ta amfani da masu haɗin tsiri na LED ko soldering.
Amma duk LED tubes cuttable? Ko duk masu haɗin tsiri sun dace da kowane nau'in tsiri na LED? Watakila, tambayoyi dubu irin waɗannan suna buga zuciyarka. Babu damuwa, wannan labarin zai warware duk shakku. Anan na rufe cikakken tattaunawa game da tsarin yanke & sake haɗawa na fitilun LED, magance matsalar yanke tsiri, da ƙari. Don haka, ba tare da wani bata lokaci ba, bari mu shiga cikin tattaunawar-
Menene LED Strip Light?
LED tsiri fitilu ne super M bugu na kewaye allo (PCB) inda LEDs masu hawa sama suke cika cikin tsari mai tsari. Ana kiran waɗannan tsiri sau da yawa LED tef ko ribbon don tsarinsu mai kama da igiya. LED tube yawanci zo da wani m goyon baya ba ka damar shigar da su daidai a saman. Ƙari ga haka, waɗannan sun shahara saboda ƙarfinsu, ƙarfin kuzari, haske, da zaɓuɓɓukan canza launi.
Gaskiya mafi ban sha'awa game da waɗannan filaye na LED shine daidaitawar su. Kuna iya ba da rai ga ra'ayoyin hasken ku na DIY tare da waɗannan tsiri. Bugu da ƙari, za ku sami ɗimbin bambancin haske tare da su, ciki har da RGB, farar fata, LED tubes addressable, da sauransu. Kuma sun dace don haskaka ɗakin kwanan ku, gidan wanka, kicin, ofis, ko hasken waje. Bayan haka, girman waɗannan filayen LED yana da sauƙin gaske. Godiya ga alamomin yanke waɗanda ke ba da damar girman raƙuman da tsayin da kuke so.
Za a iya Yanke Fitilar Fitilar LED?
Yawancin lokaci, fitilun LED suna zuwa a cikin reel na mita 5. Amma menene idan buƙatun ku shine kawai mita 1 ko 2? Ba damuwa. Filayen LED suna da alamun yanke a cikin allon kewayawa, yana ba ku damar girman su zuwa ma'aunin da kuke buƙata. Ana sanya waɗannan alamomin inda ɗaya kewayawa ya ƙare ɗayan kuma ya fara. Bayan waɗannan alamun, zaku iya yanke igiyoyin LED da sauri ta amfani da almakashi. Amma duk nau'ikan tube na LED ba a yanke su ba. Kuna iya yanke tsiri kawai tare da alamar yanke a cikinsu.
Amma yadda za a gane alamun yanke? Nemo alamomin yanke yana da sauƙin gaske. Za ku ga gumakan almakashi a cikin filayen LED. Dige-dige guda biyu na jan karfe yawanci suna yiwa waɗannan alamomin a ƙarshen kewaye. Duk waɗannan ɗigogi da gumakan almakashi suna nuna cewa yanke tsiri akan waɗannan maki ba zai lalata LED ɗin ba. Don haka, idan kuna buƙatar rage tsayin tsiri, yanke sassan zuwa girman da kuke so bin gumakan alamar yanke. Amma, yanke igiyoyi a wurin da ba daidai ba zai lalata da'ira, kuma LEDs ba za su yi haske ba. Don haka, yi hankali yayin yankan tube. Duk da haka, kada ku damu; wannan labarin zai shiryar da ku a yankan LED tube kamar pro; ci gaba da karatu.
Abubuwan da za a yi la'akari da su Kafin Yanke Tayoyin LED
Yanke igiyoyin LED na iya zama kamar mai sauqi ne. Amma yanke da ba daidai ba zai iya ƙazantar da kewaye yana haifar da lahani na dindindin ga hasken wuta. Don haka, don yanke igiyoyin LED daidai, ga abubuwan da yakamata ku kiyaye:
- Wuraren Yanke
Lokacin yankan tsiri na LED, wuraren yanke shine abu na farko da za a nema. Za ku sami layi na bakin ciki da maki biyu na ƙarfe na ƙarfe a kowane gefen ɗigon LED, yana nuna maki yanke. Waɗannan maki na ƙarfe suna biye da alamar almakashi, suna tabbatar da wurin da za a yanke. Yawancin lokaci, ana samun waɗannan alamun yanke a cikin kowane LEDs 3 (12V). Koyaya, tazara tsakanin alamomin yanke ya bambanta daga alama zuwa alama.
- Nau'in Tushen LED
Daga tattaunawar da aka yi a sama, kun riga kun san tubes na LED suna yanke. Amma duk LED tube dace da yankan? Amsar ita ce babba, A'a.
Gilashin LED da ke sarrafa kwakwalwan mutum ko IC ba su dace da yanke ba. Misali- Kuna iya yanke igiyar LED ta RGB, amma RGBIC LED tsiri ba za a iya yankewa ba saboda samun kwakwalwan IC a ciki. A cikin irin wannan nau'in tsiri na LED, ana sanya kwakwalwan kwamfuta na IC bayan kowane diodes. Suna sarrafa diodes daban-daban suna ba da damar kowane sashe don nuna launuka daban-daban tare da igiyoyin LED. Don haka idan kun yanke waɗannan tsiri, da'irar gabaɗayan sashe za ta lalace.
Amma ta yaya za ku san idan tsiri yana da yankewa, ko kuma yadda za a gano idan yana da kwakwalwan IC? Amsar ita ce madaidaiciya. Jeka alamar almakashi. Gilashin da ke da alamar almakashi suna da kyau don yankan. Kuma wadanda ba su da tambari, a guji yanke su.
- Kayan Kashewa
Yanke filayen LED ba lallai bane ya buƙaci kayan aiki na musamman. Kuna iya yanke su kawai da almakashi na yau da kullun ko kaifi mai kaifi. Amma idan yanke ya bi ta cikin kewaye, zai kawo cikas ga hasken tsiri. Abin da ya sa LED tsiri haske abun yanka ya fi kyau zama a cikin mafi aminci yankin. Waɗannan suna da tsari mai kama da almakashi tare da yankan tsinken bakin karfe na bakin karfe. Waɗannan ruwan wukake suna tabbatar da yankan raƙuman santsi, suna rage yuwuwar yanke ba daidai ba. Don haka, yi amfani da wannan kayan aikin don yanke igiyoyin LED ɗinku kamar pro.
Yadda Ake Yanke Tayoyin LED?
Yanke igiyoyin LED ba kimiyyar roka bane. Kowa zai iya yanke tafiye-tafiye da sauri zuwa girman da yake so. Anan akwai matakan da za ku iya yanke ciyawar ku daidai a cikin sauri mafi sauri.
Mataki: 1- Auna Tsawon
Mataki na farko don yanke tsiri na LED shine auna tsawon da ake buƙata don hasken ku. Don yin wannan, zaku iya amfani da tef ɗin aunawa ko kawai sanya filayen LED akan saman kashi-kashi don ƙaddamar da wurin yanke.
Spet:2- Nemo Alamomin Yankan
Bayan kun auna tsayin da ake buƙata, lokaci yayi da za a yanke igiyoyin LED. Don haka, duba alamun da aka sanya kusa da tsayin da kuke so. Koyaya, samun tube na LED tare da ƙarin alamun yankan koyaushe yana da kyau. Wannan yana nufin za a sami raguwar tazara tsakanin alamomin yanke. Kuma zai sa girman ku ya fi daidai. Misali, filayen LED tare da alamomin yanke bayan kowane LEDs guda uku sun fi dacewa da girman girman waɗanda ke da tazara na yanke alamar LED guda shida. Da zarar kun saita wurin yanke, niyya don yin almakashi kuma ku shirya yanke.
Mataki na 3- Yanke Da Almakashi
Yanzu ɗauki abin yankan tsiri na LED ko almakashi na yau da kullun tare da kaifi mai kaifi. Sanya almakashi tsakanin wurin siyar da ƙarfe, daidai inda zaku sami alamar almakashi. Tabbatar sanya abin yanka a daidai alamar. Yanzu, yanke tube. Don haka, tsirinku ya kasu kashi biyu, inda sassan biyu ke aiki daidai.
Ta wannan hanyar, bin waɗannan matakai masu sauƙi, zaku iya saurin girman filayen LED ɗin ku da kanku ba tare da taimakon ƙwararru ba.
Yadda Ake Haɗa Tushen LED?
Bayan yankan filayen LED, wani lokaci zaka iya samun tsayin gajere. A wannan yanayin, dole ne ka sake haɗa su don kawo girman da ya dace. Hakazalika, zaku iya haɗa ɗigon ɗigon ruwa lokacin da kuke buƙatar dogayen tsiri don shigarwar ku. Amma ta yaya za a yi haka?
A cikin waɗannan yanayi, zaku iya amfani da hanyoyi guda biyu don haɗa igiyoyin LED - yi amfani da masu haɗin igiyar LED ko tafi don siyarwa. Anan na tattauna tsarin haɗa igiyoyin LED guda biyu. Tafi cikin matakan kuma zaɓi hanyar da kuka ga mafi dacewa-
Tsari: 1- Amfani da Masu Haɗin Tushen LED:
LED tsiri masu haɗawa sune hanya mafi dacewa don haɗa igiyoyin LED. An ƙera waɗannan ƙananan haɗe-haɗe don kammala da'irar lantarki tsakanin igiyoyi suna yin haske. Don haka yana ba da mafita mai sauri tare da matsalar sifili na soldering. Anan akwai matakan da za ku iya haɗa igiyoyin LED kamar pro-
Mataki-1: Sayi Masu Haɗin Tushen LED Dama
Mataki na farko don haɗa ɗigon LED tare da mai haɗawa shine siyan daidai. Duk masu haɗin tsiri ba su dace da kowane nau'in tsiri na LED ba. Misali- idan kuna da tsiri LED mai launi ɗaya, siyan mai haɗin igiyar LED mai 2-pin. Kuma idan ta RGB LED tsiri ne, je don masu haɗin 4-pin. Hakanan, abin da ake buƙata na masu haɗawa ya bambanta da nau'in tsiri. Zan tattauna wannan dalla-dalla a rabin ƙarshen labarin, don haka ci gaba da karantawa. Koyaya, don siyan mafi kyawun masu haɗin tsiri na LED, je don LEDYi. Muna da babban kewayon masu haɗin tsiri na LED don nau'ikan iri daban-daban da ƙimar IP. Babban yawa kuma COB LED tsiri Hakanan akwai masu haɗawa. Don haka, duba waɗannan- LEDYi LED Strip Connector.
Mataki-2: Kwarewar Tef Baya
Da zarar kana da madaidaicin mai haɗin tsiri, lokaci ya yi da za a shiga babban aikin. Ɗauki fitattun LED ɗin kuma yayyage ɗan yanki na goyon bayan tef ɗin 3M daga sashin da kuka riga kuka yanke. Idan tsiri naku sabo ne kuma har yanzu kuna buƙatar yankewa, nemi alamar yanke ƙarshen kuma yanke naúrar don cire wani tef ɗin mannewa. Wannan aikin peeling yana tabbatar da tsiri na LED yana zaune daidai lokacin da aka saka shi cikin mahaɗin.
Mataki-3: Sanya Tushen LED Zuwa Mai Haɗi
Ɗauki mai haɗawa kuma saka wurin ƙarewa na sassan biyu a cikin mahaɗin. Tabbatar da tabbataccen (+) & korau (-) alamar ratsi yayi daidai da na mai haɗin. Har ila yau, tabbatar da cewa kayan sayar da kayan sun haɗa da haɗin gwiwa gaba ɗaya.
Mataki-4: Rufe Mai Haɗi
Bayan shigar da tsiri LED a cikin mahaɗin, kulle shi da murfin filastik. Yi hankali kuma tabbatar an saita murfin daidai. Hakanan, sau biyu duba tabbatacce (+) & alamomin (-) masu kyau don tabbatar da an sanya su daidai. Koyaya, tef ɗin ruwa ko kayan haɗin gwiwa na iya sa haɗin ya fi ƙarfi. Zai ci gaba da haɗin gwiwa tsakanin raƙuman raƙuman ruwa, rage yawan damar samun sako-sako.
Hanya-2: Sayar
Siyar da ita shine mafi amintaccen hanyar haɗin igiyar LED don dorewa da haɗin kai mai mahimmanci. Don haka, idan kuna son haɗin kai na dindindin da ƙwararru don masu tayar da hankali na LED, bi tsarin siyarwar ƙasa-
Mataki-1: Kwasfa da manne daga faifan Solder
Ɗauki filayen LED kuma tabbatar da ƙarshen sassan biyu suna da yanke mai kyau. Yanzu a hankali kwasfa goyan bayan m 3M daga kushin sayar da ɗayan filayen LED. Wannan tsiri mai goyan bayan bawon zai kasance a saman lokacin da aka sayar da shi.
Mataki-2: Dumama & Neman Solder
Yanzu, pre-farantin solder pads a kan sashin tsiri wanda za a sanya a ƙarƙashin ɗayan. Kada ka taɓa dumama mai saida kai tsaye; ko da yaushe zafi da manufa yankin. Da zarar an shafa isasshen zafi a wurin, lokaci ya yi da za a sayar da shi. Ya kamata ku shafa solder zuwa wuri mai zafi; kaucewa sanya sojan kai tsaye cikin bakin karfe.
Mataki-3: Haɗa Tsari
Bayan haka, jera sashin tsiri da ba a saka ba kai tsaye a kan sabbin mashin ɗin sannan a shafa zafi. Rike iron ɗin a wurin har sai mai siyar ya narke ya fara zubowa. Koyaya, tabbatar da tsiri baya yin zafi sosai, ko kuma yanayin da'irar na iya fara ɗagawa daga ma'aunin PCB. Ta wannan hanyar, za a haɗa igiyoyin ku tare. Ƙara ƙaramin yanki na solder a saman kushin don ƙarfafa haɗin gwiwa. Wannan zai sa haɗin gwiwa ya yi ƙarfi kuma ya inganta sha'awar gani na tsiri.
Nau'o'in Masu Haɗin Tushen LED
LED tsiri haši na iya zama da yawa iri dangane daban-daban Categories, kamar-PINs, IP rating, aiki, da dai sauransu Wadannan iri LED tube connectors ne kamar haka-
Masu Haɗin Rigar LED Dangane da PIN
Dangane da PINs, masu haɗin tsiri na LED na iya zama nau'ikan masu zuwa:
- 2 PINs LED tsiri masu haɗawa: Waɗannan masu haɗawa sun dace da igiyoyin LED masu launi ɗaya ko fari. Kuna iya amfani da waɗannan masu haɗawa tare da LEDYi ɗin mu igiyoyin LED masu launi ɗaya. Muna da ja, koren, shuɗi, rawaya, amber, ruwan hoda, da launuka UV akan filayen LED ɗin mu masu launi ɗaya. Koyaya, muna kuma samar da wuraren OEM & ODM. Don haka, tuntuɓe mu idan kuna buƙatar kowane gyare-gyare.
- 3 PINs LED tsiri masu haɗawa: Masu haɗin tsiri na LED tare da fil uku sun dace da su CCT daidaitacce da dual launi LED tube. Waɗannan masu haɗin haɗin suna da kyau idan kuna da filaye masu farar fata na LED ko filayen LED masu magana.
- 4 PINs LED tsiri masu haɗawa: RGB LED tsiri sun dace da 4 PINs LED tsiri haši.
- 5 PINs LED tsiri masu haɗawa: Waɗannan masu haɗin suna haɗa RGB+W ko RGBW LED tsiri.
- 6 PINs LED tsiri masu haɗawa: Idan kana da RGB + CCT ko RGB+ Farar fitilun LED mai kunnawa, za ku buƙaci masu haɗin PIN 6 don shiga cikin sassan.
| Lambobin PIN Don Masu Haɗin Tsari | Nau'in Tushen LED |
| 2 PIN | Gilashin LED masu launi ɗaya. |
| 3 PIN | Matsakaicin farar fata na LED & Fitilar LED masu magana |
| 4 PIN | RGB LED tsiri |
| 5 PIN | RGB + W ko RGBW LED tube |
| 6 PIN | RGB+CCT & RGB+Tunable farin tube LED |
Masu Haɗin Gilashin LED Dangane da Lambar IP
IP rating yana tsaye ga Ci gaban Ci gaba. Yana ƙayyade matakin kariya daga ƙaƙƙarfan shigar ruwa da ruwa. Dangane da wannan factor, LED tsiri haši na iya zama daga cikin wadannan iri-
- IP20-Ba mai hana ruwa ba: Waɗannan masu haɗin tsiri na LED ba su da ruwa. Kuna iya amfani da su tare da ƙananan igiyoyin LED masu ƙima na IP don amfanin cikin gida, ɗakin zama kamar ɗakin kwana, da sauransu.
- IP52-Rufin Gefe Guda Guda: Fitilar LED mai hana ƙura tare da IP52 sun dace da waɗannan masu haɗin tsiri. Tsayin waɗannan masu haɗawa ya fi masu haɗin IP20 girma, yayin da suke haɗuwa da tube tare da gashin manne gefe guda ɗaya.
- IP65-Hollow Tube Mai hana ruwa: Ana haɗa igiyoyin LED tare da ƙimar IP65 ta amfani da wannan haɗin. Su kura ne da hana ruwa. Don haka za ku iya amfani da su a cikin ɗakin dafa abinci, gidan wanka, da eaves.
- IP67/IP68-Tsarin Tube Mai hana ruwa: Idan kana neman cikakken mai haɗin ruwa mai hana ruwa don igiyoyin LED ɗinku tare da ƙimar IP67/68, masu haɗin tube mai hana ruwa mai ƙarfi sun fi kyau. An rufe su gabaɗaya kuma ba za su bari ruwa ya shiga haɗin tube ba.
Masu Haɗin Gilashin LED Dangane da Tsarin & Aiki
Dangane da tsari & aiki, LED tube na iya zama daga cikin wadannan iri-
- COB LED tsiri mai haɗawa: Waɗannan masu haɗin tsiri na LED sun dace da tube LED COB. Waɗannan kuma ana kiran su da haɗin ƙwaro marar ganuwa. Kuna iya zuwa LEDY ɗin mu COB LED tsiri masu haɗawa; sun kasance a bayyane isa don haɓaka tasirin haske mai girma na COB LED.
- LED Strip 90-Degree connector: Ana amfani da mahaɗa mai siffar 'L' don haɗa igiyoyi a kusurwa ko gefuna, wanda aka sani da mai haɗin digiri 90. Waɗannan ƙananan na'urori suna da tsarin L-fattern tare da masu haɗawa a ƙarshen duka. Yana ba ka damar haɗa guda biyu na fitilun LED ta hanyar saka su cikin waɗannan haɗin biyu. Don koyon tsarin haɗin waɗannan masu haɗin, duba wannan bidiyon - Sabuwar L Shape Solderless Connector.
- Hippo-M LED Strip Connector: Waɗannan ƙwararrun masu haɗin gwiwar ƙwararrun ƙwararrun ƙwararrun ƙwararrun ƙwararrun ƙwararrun ƙwararrun ƙwararrun ƙwararru suna goyan bayan fitattun filayen LED. Fasahar tuntuɓar raɗaɗin waɗannan masu haɗawa tana sa haɗin ya zama mai sauƙi da dacewa.
Masu Haɗin Gilashin LED Bisa Faɗin PCB
Dangane da PCB na filayen LED, masu haɗawa na iya zama na waɗannan nau'ikan-
- 5MM
- 8MM
- 10MM
- 12MM
Bayan waɗannan ma'auni, idan kuna buƙatar kowane gyare-gyare, tuntuɓi LEDYi. Muna samar da ingantattun masu haɗin tsiri na LED tare da wuraren gyare-gyare.
LED Strip Connectors Bisa Nau'in Haɗin
Dangane da bambancin haɗin kai, masu haɗin igiyoyi na LED na iya zama nau'ikan masu zuwa:
- Tafi zuwa Waya
- Tafi zuwa Ƙarfi
- Tafi zuwa Rage haɗin gwiwa
- Tafiya zuwa Gadar Tsibiri (Jumper)
- Haɗin Kusurwa
- Tsalle zuwa sauran Adaftar Haɗi
Sayar da Vs. LED Strip Connector
Kun riga kun koyi game da hanyoyin haɗin igiyar LED guda biyu daga sashin da ke sama. Yanzu bari mu gano bambance-bambancen da mafi kyau a tsakanin su-
| Dalili | Soja | LED Strip Connector |
| Stability | high | m |
| saukaka | Ƙananan Sauƙi | Babban Sauƙi |
| Maintenance | Hard | Easy |
| Hanyar Koyo | Da wuya a koya | Easy |
| cost | Mafi girma | Lower |
Jadawalin da ke sama yana nuna bambance-bambance tsakanin masu haɗa siyar da LED tsiri, amma wanne ya fi kyau? Don samun amsar, bari mu kwatanta waɗannan biyun daki-daki-
Stability: An yi masu haɗin tsiri na LED da filastik, waɗanda za su iya faɗaɗa ko kwangila lokacin shigar da su a cikin yanayi mai tsananin zafi. Bayan haka, masu haɗin tsiri na iya sassauta haɗin gwiwa lokacin da aka sanya filayen LED akan wani wuri mai girgiza ci gaba. A cikin waɗannan lokuta, tafiya don siyarwa shine mafi kyawun zaɓi. Sayarwa yana tabbatar da haɗin kai mai ƙarfi tsakanin igiyoyin kuma yana ba su damar manne da juna. Wato, soldering ya fi kwanciyar hankali da dogaro fiye da masu haɗin tsiri na LED.
Aminci: Lokacin da ake buƙatar shiga cikin tube na LED, zaɓin koyaushe zai kasance yana gyara hakan ta hanya mafi sauƙi. Amma ba koyaushe za ku sami ƙarfe a hannu ba. A wannan yanayin, masu haɗin tsiri na LED sune mafita na ƙarshe. Suna da sauƙin samuwa da sauƙi don amfani. Don haka, dangane da dacewa, masu haɗin tsiri na LED sun fi soldering.
Taimako: Saboda rashin kyawun siyar da SMD, rashin isassun zafin zafi, masu tsayayya mara kyau, kwakwalwan LED mara kyau, da sauransu, tube LED na iya buƙatar sauyawa. Kuma idan an haɗa ɗigon ta amfani da hanyar haɗi, maye gurbin tsiri mai lalacewa abu ne mai sauƙi. Kuna iya buɗe mai haɗawa da sauri fitar da tsiri. Amma idan an sayar da tsiri, dole ne a tuntuɓi ƙwararren masanin lantarki don gyara wannan. Don haka, kiyaye tube na LED tare da masu haɗawa ya fi sauƙi fiye da soldering.
Hanyar Koyo: Idan kai ba ma'aikacin lantarki bane, saida kayan aiki ne mai wahala don koyo. Koyaya, yin amfani da haɗin kai yana da sauƙi don haka ba za ku buƙaci koyon fasaha ba. Bayan haka, ba kwa buƙatar damuwa game da polarity mara kyau saboda zaku iya cire haɗin da sauri da gyara batun. Bugu da ƙari, ƙonewa ba batun damuwa ba ne tare da masu haɗawa, kuma ba warin rosin ba ne. Sabanin haka, siyar da ƙarfe na iya yin zafi kamar 300°C/570°F, wanda zai iya zama mai haɗari. A wannan ma'anar, masu haɗin tsiri na LED sun fi kyau kuma sun fi aminci, musamman idan ba ku da ƙwararru.
Kudin: Kuna iya samun masu haɗin tsiri na LED a cikin dala ɗaya. Sabanin haka, siyarwar yana buƙatar kayan aiki kamar ƙarfe mai siyar da ƙwararren mai aikin lantarki. Wannan ya sa saida yayi tsada.
Don haka, idan aka kwatanta duk waɗannan abubuwan, zamu iya cewa masu haɗin tsiri na LED sun fi kyau idan kuna son mafita mai sauƙi, mai sauri, da araha don haɗa raƙuman LED ɗin ku. Koyaya, don ƙarin kwanciyar hankali da aminci, tafiya don siyarwar ya fi kyau.
Duk Sashe na LED Strip Zai Yi Aiki Bayan Yanke?
Dukansu sassa na LED tsiri za su yi aiki lafiya idan ka yanke su a daidai alamar kuma ka haɗa su daidai.
Yawancin filayen LED suna da alamun yanke irin wannan. A cikin fitilun LED, zaku sami wasu rufin jan ƙarfe bayan kowane ƴan LEDs (3 ko 6 ko fiye). Tsakanin waɗannan labulen tagulla, akwai alamar almakashi. Wannan alamar tana nuna alamun yanke. Idan kun yanke tsiri daidai a wannan wurin, tabbas tsirinku zai yi aiki.
Amma idan ka yanke a wurin da ba daidai ba, da'irar LED kusa da yanke za ta lalace, kuma LED ɗin ba zai haskaka ba. Bayan lalacewa ta dindindin, kuna iya fuskantar wasu batutuwa kamar flickering, rufewar kwatsam, da sauransu. Don haka, a yi hattara lokacin yanke igiyoyin LED.
Yadda Ake Sanya Fitilar Fitilar LED Bayan Yanke?
Da zarar ka yanke fitilun LED ɗinka gwargwadon tsayin da ake buƙata, lokaci yayi da za a saka su. Anan ga matakai don shigar da tube na LED-
Mataki-1: Tsaftace & Busasshen Tsarin Shigarwa
Bayan yin girman tsiri na LED ɗinku, mataki na farko shine tsaftace farfajiyar shigarwa. Ɗauki zane mai tsabta da ƙura daga bangon da kyau. Idan ka ga saman yayi datti sosai, yi amfani da sabulu, barasa, ko phenol don tsaftace shi. Kuma bayan tsaftacewa, bari saman ya bushe gaba daya. Wannan mataki ne mai mahimmanci, kamar yadda goyon bayan m ba zai zauna ba idan akwai ƙura da datti a bango. Don haka, kar a taɓa tsallake wannan matakin.
Mataki-2: Kwasfa Kashe Tallafin Adhesive
Tabbatar cewa saman ku ya bushe gaba ɗaya kuma ya bushe, yanzu lokaci yayi da za a fara aikin shigarwa. Don wannan juya fitilun LED, zaku sami goyan bayan m. Cire sitika kuma shirya don hawan igiyoyin.
Mataki-3: Dutsen Dutsen LED
Sanya sassan a wurin da ake so, kuma danna su da yatsa. Wannan zai bar tsiri ya tsaya a saman daidai. Anan, zaku iya amfani da wasu shirye-shiryen bidiyo don tabbatar da cewa ɗigon ba su faɗo daga bango cikin sauƙi ba. Koyaya, a cikin yin amfani da manne, la'akari da nau'in saman yana da mahimmanci. Misali- shigar da filaye na LED tare da goyan bayan mannewa yayi kyau don itace, filastik, ƙarfe, vinyl, ko kowane wuri mai santsi. Amma a saman da aka zana, kamar bawo na lemu ko fentin busasshen bango, manne zai goge bayan lokaci. Kuna iya amfani da shirye-shiryen bidiyo ko tashoshi don shigar da fitattun LED a wannan yanayin. Don ƙarin sani game da tsarin hawan igiyar LED, duba Shigar da Tushen Flex LED: Dabarun Haɗuwa.
Mataki-4: Haɗa shi zuwa Wutar Lantarki
Da zarar an ɗora tsiri na LED ɗin ku, lokaci yayi da za a kunna shi. Haɗa tsiri na LED zuwa mai sarrafawa sannan zuwa tushen wutar lantarki. Yanzu kunna maɓallin kuma duba LEDs ɗin ku suna haskakawa. Idan hasken bai yi haske ba, duba idan an haɗa mai sarrafawa daidai kuma idan wutar lantarki ta tushen wutar lantarki ta yi daidai da igiyoyin LED. Koyaya, idan batun ya shafi yanke tsiri mara kyau, duba sashin da ke ƙasa don nemo mafita.
Shirya matsala: LED Strip Ba Aiki Bayan Yanke
LED tsiri iya nuna wasu al'amurran da suka shafi bayan yankan. Waɗannan na iya haɗawa da- kyalkyali, matsalolin haske, ko cikakken rufe fitilu. Don magance wannan matsala, da farko, kuna buƙatar sanin dalilin irin waɗannan batutuwa-
Dalilin: Bayan yankan filayen LED, zaku iya ganin tsirin ba ya aiki. Ko rabin yanki na yanke yana aiki; dayan kuma ba. Hakanan waɗannan batutuwa na iya faruwa lokacin da kuka sake haɗa igiyoyi biyu. Ga musabbabin wadannan batutuwa-
- Yanke ɗigon LED wanda ba a yankewa: Duk filayen LED ba a yanke su ba. Don haka, idan kun yanke tsiri na LED ba tare da alamar yanke ba, ba zai yi aiki ba.
- Yanke kuskure: Filayen LED suna da alamun yanke a kansu. Wannan yana nuni da cewa wata da’ira ta kare wata kuma ta fara; yankan a wannan lokacin yana da lafiya. Amma idan ka yanke su a wani wuri sai dai alamar yanke, zai lalata kewaye, kuma LEDs ba za su yi haske ba.
- Polarity mara daidai: Idan an haɗa igiyoyin LED zuwa wutar lantarki tare da haɗin polar da ba daidai ba, hasken ba zai yi aiki ba bayan yanke igiyoyin LED. Misali- haɗa tabbataccen (+) zuwa mara kyau(-) ba zai yi aiki ba.
Magani: Anan shine mafita wanda zaku iya amfani dashi don gyara tsiri na LED-
- Duba ga sako-sako da haɗi: Lokacin amfani da masu haɗin tsiri na LED don haɗa igiyoyin LED bayan yanke, haɗawar na iya sassautawa. Wani lokaci, haɗin tsakanin wutar lantarki kuma na iya yin sako-sako da shi, yana kashe fitilun. A wannan yanayin, bincika haɗin kuma gyara shi idan kun sami sako-sako.
- Sake yanke kuma sake haɗawa: Filayen LED ɗin za su daina aiki saboda yanke ba daidai ba. Don gyara wannan batu, an riga an riga an yi alamar yanke maki kuma yanke su a can. Kuma yanzu sake haɗa igiyoyi ta amfani da haɗin kai ko sojoji. Za ku ga tsiri yana aiki daidai.
- Tabbatar da polarity daidai: LED tube dole ne ya kasance da daidai polarity lokacin da aka haɗa zuwa wasu tube. Wato, tabbatacce (+) dole ne ya hadu da tabbatacce (+) & korau (-) zuwa korau (-). Don haka, tabbatar da haka; LED tsirinku zai fara haske.
Duk da haka, idan wannan maganin bai yi aiki ba, gano idan akwai wani kuskuren masana'anta tare da daidaitawa. Kuma tuntuɓi ma'aikacin lantarki idan kun gaza magance matsalar.
Don ƙarin bayani, kuna iya karantawa Shirya matsala Matsalolin Tsibirin LED.
FAQs
Kwayar
Don haka, daga tattaunawar da ke sama, mun koyi cewa filayen LED suna da yankewa kuma ana iya sake haɗa su. Suna da gumakan almakashi akan PCB ɗin su, wanda ke nuna alamar yankan. Bayan waɗannan maki, zaku iya yanke su da sauri zuwa ma'aunin da kuke buƙata ta amfani da almakashi. Amma duk LED tube ba dace da yankan, watau, RGBIC LED tube. Haɗaɗɗen da'irar da aka shigar a cikin su baya ba ku damar yin yanke kowane tsiri.
Koyaya, bayan yanke tsiri na LED, yana yiwuwa a sake haɗa su. Don yin wannan, za ka iya amfani da LED tsiri haši ko soldering. Soldering wani tsari ne na al'ada don shiga filayen LED. Kodayake soldering yana ba da ƙarin kwanciyar hankali ga haɗin tsiri, wannan tsari yana da ƙalubale ga jama'a. Yana buƙatar ƙarfe wanda ƙwararru kawai za su iya sarrafa daidai. Sabanin haka, masu haɗin tsiri na LED sune mafi sauƙi kuma mafi kyawun mafita don sake haɗa tsiri na LED. Waɗannan ƙananan haɗe-haɗe na filastik suna haɗuwa da raƙuman ruwa kuma suna tabbatar da ingantaccen kwararar halin yanzu. Bayan haka, waɗannan na'urorin haɗi suna da araha kuma suna samuwa, kuma kowa yana iya amfani da su cikin sauƙi. Don haka, idan kuna son sake haɗa raƙuman LED da kanku ko tsara kowane fitilun tsiri na DIY, masu haɗin tsiri na LEDYi sune mafi kyawun mafita!
LEDYi yana da tarin tarin masu haɗin tsiri dangane da PIN, ƙimar IP, nau'ikan haɗin gwiwa, da ƙari. Don haka, ban da ƙimar mu LED tsiri, za ka iya kuma zuwa ga high quality- & m LED tsiri masu haɗawa.
